Kuhn Knight

***Consigned*** 1999 Kenworth W900 with Knight PSC181 Manure Spreader! Vertical Beaters, hydraulic controls, good webs, good beaters but could use some new beater teeth! Truck has 142,000 miles, 5663 hours, ISM305V Cummins motor, transmission is a Eaton Fuller 13 speed, all wheel drive Marmon Herrington! Very nice truck! Ready to go!

***As with all consigned equipment the 60 day warranty does not apply***

***Consigned*** Kuhn Knight 3170 Reel Feed Mixer! Single axel, slide tray discharge, augers are getting thinner but still have some life, full stainless steel liners, all new diamond chains within the last 2 years, good reel! Small 1000 PTO, Digi-Star scale head, bucket guards! Ready to go!

– Replacement Sectional Flight
– 14, 10, 4, .25, RH, HOLES
– KK, 134740, 134741, 134742

– Left Hand Direction
– 15-5/8″ Diameter
– 16″ Pitch
– 4″ Inside Diameter
– .38″ thick
– 6 notch design
– Holes for Knife mounting
– Mild Steel
– Knives not included

“- Mild Steel
– Formed
– 15.63″ Outside Diameter
– 16″ Pitch
– .38” Thick
– Right Hand Direction
– 6 Notch Design
– Holes placed for Knife Mounting
– Knives not included
– KK133832

– Left Hand Direction
– 20″ Diameter
– 16″ Pitch
– 8-5/8″ Inside Diameter
– .25″ thick
– Smooth Edge
– Holes for Knife mounting
– Mild Steel
– Knives not included

– Left Hand Direction
– 18″ Diameter
– 14″ Pitch
– 5-9/16″” Inside Diameter
– .25″ thick
– Smooth Edge
– Holes for Knife mounting
– Mild Steel
– Knives not included

• Kuhn Knight Replacement Beater Tooth
• Bolt on
• Bolts Not Included
• High Ware
• Left Hand Tip
• Vertical Beaters
• Vertical Spreaders
• MILD STEEL

Vertical Manure Spreader, Replacement Beater Teeth, Kuhn Knight

• Kuhn Knight Replacement Beater Tooth
• Bolt on
• Bolts Not Included
• High Ware
• Right Hand Tip
• Vertical Beaters
• Vertical Spreaders
• MILD STEEL

• Kuhn Knight Replacement Beater Tooth
• AR400
• Bolt on
• Bolts Not Included
• High Ware
• Right Hand Tip
• Vertical Beaters
• Vertical Spreaders

– Fits 3 & 4 Auger Discharges
– Bronze
– 1.38 ID x 1.625 OD x 1.5″

– Fits to 3 & 4 Auger Discharges
– Bronze
– 1.38 ID

• 3 & 4 Auger TMR Mixer Discharge Sizes
• Replacement Feed Mixer Discharge Auger
• 43″ Overall Length To End of Shaft

– Replacement Shred Flail
– Bale Shredding Replacement Tips
– 5/8″ X 4″ Grade 8 Bolt
– Fits all Haybuster Model Bale Shredders

– Left Hand Direction
– 14″ Diameter
– 10″ Pitch
– 4″ Inside Diameter
– .25″ thick
– Smooth Edge
– Holes for Knife mounting
– Mild Steel
– Knives not included

-TMR Feed Mixer Spindle
-#12,000
-3″x20″
-PTA2041

Both units were new in 2013 very nice local trade! Left hand discharge, Digi-star 2400V scale with remote, all stainless liners, top auger is 50% or so new bottom auger and reel wipers! Truck has full aluminum rims with good tires, truck is freshly serviced, has and automatic Allison 3500 RDS transmission, motor is a Paccar PX-8 300hp, very clean super sharp one owner unit, truck will have around 9000 hours with 53,000 miles. Ready to feed cattle!

– Vertical Mixer Knife
– Feed Wagon Knife
– TMR Mixer Blade
– 20″ Style Knife
– Hardware Included

Used Knight 2250 Reel Feed Mixer Wagon! Good three foot 3-auger discharge, augers are 70-80% or so, has been relined, 3 bar reel, all functions work as they should, good mechanical condition! Will be sold as is, 540 PTO, Weigh-Tronix scale head! Ready to go!

Used Knight 2450 Reel Mixer Wagon! Slide tray discharge with magnets, top auger is 60%, bottom auger is 50%, good liners, small 1000 PTO, Weigh-Tronix scale head! Ready to go!

Used Knight 2450 Reel Mixer Wagon! New slide tray discharge with magnets, 540 PTO, Digi-Star scale head! Good auger liners with one new section, augers are 50% or so, good liners! Ready to go!

Used Knight 3030 Reel Mixer Wagon! Good 3-auger discharge with new augers and new mag tip off, 540 PTO, newer auger liner by door, Digi-Star scale head! Nice used mixer! New auger liners in the back half, good reel liners! Ready to go!

Used Kuhn Knight 3036 Reel Mixer Wagon! Nice wagon! LH 3-auger discharge, 385 tires, augers in good condition! New auger and reel liners, J-Star scale head, 540 PTO! Ready to go!

Used Knight 3036 Reel Mixer Wagon! Left hand slide tray discharge with magnets, bottom auger at 80%, top auger at 45% or so, good liners, J-Star scale head, 540 PTO. Nice mixer! Ready to go!

Used Knight 3042 Reel Feed Mixer! Three foot three auger discharge with magnet tip off, good bottom auger with some new flighting by the door, top auger is ok, new auger liner up front! Digi-Star scale head, 540 PTO, nice straight older mixer! Ready to go!

**Consigned**Knight 3060 Pete TM, truck has roughly 123,000 miles, 320 model, PACCAR PX-9 engine, left hand flip-up discharge, stainless liners, 4 reel bars, dual augers.

**This unit is consigned 60-day warranty does not apply**

Used Knight 3136 Reel Feed Mixer! LH slide tray discharge with magnets, good bottom auger, top auger is around 40% or so, newer wiper plastic, Digi-star 2810 scale head, single axle with 385 tires! Very nice mixer! Ready to go!

Used Kuhn Knight 3136 Reel Feed Mixer! New slide tray assembly 3 months ago, stainless auger liner by the door, bottom auger flighting is good at 80% or so! Top auger flights are 40% or so, good liners! Nice looking wagon! Ready to go!

Used Knight 3136 Reel Mixer Wagon! Nice straight mixer! 3′ 3-auger discharge, new auger liners, good bottom auger with new flights by the door, new top auger flights! 540 PTO, Weigh-Tronix Scale head! Ready to go!

Used Knight 3136 Reel Mixer Wagon! Nice Mixer! Good LH 3-auger discharge with mag tray tip off, augers are at 50% or so, liners are good, Weigh-Tronix scale head with remote display! Ready to go!

Used Knight 3150 Reel Feed Mixer! Slide tray discharge, single axel, good augers, newer mild steel reel liners, newer auger liners with stainless steel by the door, Digi-Star scale and LH remote display, 540 PTO, rear light kit! Nice looking mixer! Ready to go!

Used Knight 3300 Reel Feed Mixer! Three foot 3 auger discharge with magnet tip off, has had liners, bottom auger is 40% or so and top auger is 50% or so. Four bar reel, 540 CV PTO, Digi-Star scale head! Wagon will be sold “As Is” everything functions like it should. Ready to go!

Used Knight 3300 Reel Feed Mixer! New Reel liner, augers are around 70% or so, good auger liners, good 3 auger discharge! Weigh-Tronix scale head, 540 PTO! Nice straight wagon! Ready to go!

Used Knight 3300 Reel Mixer Wagon! Nice smaller cheaper wagon! Bottom auger flights are 50% or so, top auger flights at 30% or so, slide tray discharge with magnets! Reel is in working but not great condition, 540 PTO, all functions work as they should, scale head! Wagon will be sold “AS IS”. Ready to go!

NEW!! Helix reel, 3 auger discharge, partial stainless steel

Used Kuhn Knight 1140 Manure Spreader! Nice smaller spreader! Dual horizontal beater, new beater teeth on bottom beater, good top beater teeth! Tandem axel, dual webs, poly floor, 540 PTO, hyd. flow control! Ready to go!

Used Kuhn Knight 3036 Reel Mixer Wagon! Nice straight wagon! Slide tray with magnets discharge, good bottom augers at 50-60% or so, top auger has new flighting, stainless steel reel liner, stainless steel auger liner! Small 1000 PTO, Digi-Star scale head! Ready to go!

Used Knight 3042 Reel Feed Mixer! Slide tray discharge with magnets, has good liners, very good bottom auger, top auger is 50% or so, stainless steel auger liner by the door! 540 PTO, Digi-Star scale head, 5 bar reel! Ready to go!

Used Kuhn Knight 3060 Reel Mixer Wagon! Single axel, good 4-auger discharge, augers are 60% or so,  new reel liners, good stainless steel liners under the auger, 540 PTO, Weigh-Tronix scale head with RH LED remote display! Ready to go!

Used Kuhn Knight 3070 Reel Feed Mixer! Nice big wagon! Single axel, slide tray discharge with magnets, Digi-Star scale head! Good augers, good liners, small 1000 PTO, road light kit! Ready to go!

Used Kuhn Knight 3130 Reel Feed Mixer! Nice straight mixer, good 3′ three auger discharge with magnet tip off, new mild steel reel liners, new bottom auger, top auger is 40-50% or so! Digi-Star scale head, 540 PTO, good paint! Ready to go!

Used Kuhn Knight 3136 Reel Feed Mixer! Good 3′ three auger discharge, nice straight wagon, good bottom auger with a few new flights, good top auger, new auger liners! Point scale head, 5 bar reel, 540 PTO! Ready to go!

Used Kuhn Knight 3142 Reel Feed Mixer! Slide tray discharge and weigh-tronix scale head.  Coming in!

Used Kuhn Knight 3142 Reel Feed Mixer!  Has stainless liners.  Coming Soon!

Used Kuhn Knight 3142 Reel Feed Mixer! Very sharp wagon! Good three foot 3 auger discharge with magnet tip off, good augers, good liners, 540 PTO, Weigh-Tronix scale head! Ready to go!

Used Kuhn Knight 3142 Reel Feed Mixer Wagon!  Has slide tray discharge, rear light kit, Weightronix scale head, and straight bar reel.  Coming in!!

Used Kuhn Knight 3160 Reel Mixer Wagon! Single axel, slide tray discharge with magnets, small 1000 PTO, road light kit, Digi-Star scale head! Good augers, new reel liners, stainless steel under the augers, just repainted! Ready to go!

Used Kuhn Knight 3300 Reel Feed Mixer!  Has 3-auger discharge and 4 bar reel.  Coming Soon!

Used Kuhn Knight 3300 Reel Feed Mixer!  Has 36″ 3 auger discharge and Weigh-Tronix scale.  Coming Soon!

Used Kuhn Knight 3450 Reel Feed Mixer Wagon! Slide tray discharge with magnets, top auger is 40-50% or so, bottom auger is similar with new flighting by the door, new mild steel reel and auger liners! Digi-Star EZ150 Scale head, 540 PTO, nice straight mixer! Ready to go!

Used Kuhn Knight 3450 Stationary Feed Mixer! Has manual discharge door, augers are 40% or so, Digi-Star scale system, five bar reel,! Comes with some auger liners and a Emerson electric motor! All functions work as they should but mixer will be sold “As Is”. Ready to go!

Used Kuhn Knight 3700 Reel Feed Mixer! Single axel, good three foot 4-auger discharge with magnet tip off, 5 bar reel, augers are ok! Small 1000 PTO, Digi-Star scale head with remote display! Nice big reel mixer! Ready to go!

Used Kuhn Knight 4072 Botec 4-Auger Mixer Wagon! Left hand 3-auger discharge, tandem axle with duals, augers are 50% or so, good stainless steel liners, Digi-Star scale head with LED scoreboard remote read out!  Ready to go!

Used Kuhn Knight 5156 Vertical Feed Mixer! Complete rebuild! Single axel, Digi-star scale head, light kit, RH flip up conveyer! New augers, new discharge, good liners, repainted! Very sharp! Ready to go!

Used Kuhn Knight 5156 Vertical Feed Mixer! Single axel, right hand flip up discharge, good augers, good tub liners, good paint! Wagon was recently rebuilt! Clevis hitch, small 1000 PTO, light kit, Digi-Star scale head! Ready to go!

Used Kuhn Knight PS160 Vertical Beater Manure Spreader! Tandem axle with 435 tires, beavertail slop gate, rock guard, small 1000 PTO, tandem pintle web chains, light kit! Nice Knight spreader! Ready to go!

Used Kuhn Knight RA142 Reel Feed Mixer! Very sharp wagon! Slide tray discharge with magnets, helix reel, drop down side for loading, augers at 50-60%! Weigh-Tronix scale head with RH remote read out, 540 PTO. light kit! Ready to go!

Used Kuhn Knight RA142 Reel Feed Mixer! Very nice wagon! Good three foot 3-auger discharge with magnet tip off, helix reel, augers are 50%-60% or so, good reel liners, good auger liners with stainless steel by the door! Weigh-Tronix scale head with right hand remote read out, small 1000 PTO, light kit! Ready to go!

Used Kuhn Knight RC150 Reel Feed Mixer! Sharp wagon! Slide tray with magnets discharge, good paint, 4 bar reel, good augers! Small 1000 PTO, Digi-Star scale head, light kit! Ready to go!

Used Kuhn Knight RC250 Reel Feed Mixer! Very sharp wagon! Single axel with lug tires, 4 auger discharge with magnet tip off and new augers, helix reel, good augers! Small 1000 CV PTO, Weigh-Tronix scale head, road light kit! Ready to go!

Used Kuhn Knight VT144 Vertical Mixer Wagon! Single axel, left hand side door with conveyor discharge, good augers at 60% or so with hard welded edges, new auger knives! New floor liners, new tub liners, 9″ rubber extension, point scale, 540 PTO, light kit! Ready to go!

2001 model tandem axle, nice truck, spreader is a 2009, vertical beater, webs are good, slop gate

• Penta, Kuhn Knight, RotoMix, Farm Aid, NDE, Trioliet Replacement Magnet Part
• Magnet Tray Replacement Part
• Supreme Replacement Slide Tray Magnet
• Bolt In
• Replacement Magnet
• 17.5″ Magnet
• Reel Auger TMR Mixers
• Vertical TMR Mixers”

– Kuhn Knight Replacement Magnet Part
– Magnet Tray Replacement Part
– 4 Auger Tip Tray Replacement Magnet
– Supreme Replacement Slide Tray Magnet
– Bolt In
– Replacement Magnet
– 18″ Magnet
– Reel Auger TMR Mixers
– Vertical TMR Mixers
– Rotomix TMR Mixer Slide Trays

– Fit Kuhn Knight Horizontal Mixers
– Kuhn Knight Botec Mixers
– RotoMix Mixers
– Left Hand
– Hardware Not Included

– 7.5″ long
– Serrated Edge
– Bolts included
– Kuhn Knight Replacement Mixer Knife
– # KK141406

Kuhn Knight, TMR, Reel Mixer Spring
SPRING, REEL, KK, 171920, 16″

– Fits 3 & 4 auger TMR Discharges
– Tensioner Spring
– Kuhn Knight Replacement Part
– 3.94 LG

– Dual Sprocket
– 3 & 4 auger discharges
– Kuhn Knight Replacement Parts
– 50-2R-18
– 1.38″ BORE

• Kuhn Knight Replacement Parts
• TMR Mixer Reel Part
• Steel Tensioner Spring
• 3x3x16 Steel Coil
• Fits to 3025

Used Kuhn Knight 3142 Reel Feed Mixer!  Coming In!