Penta-1120HD

Penta TMR Specs

Penta TMR Specs(Click the model# to view full specifications in .pdf view)
Penta Model # Capacity Loading Height (top of 9″ rubber) Augers
Penta 2020 SD 250 cuft. 91″ Single screw
Penta 3020 SD 370 cuft. 99″ Single screw
Penta 4020 SD 470 cuft. 102″ Single screw
Penta 5020 SD 570 cuft. 108″ Single screw
Penta 6020 SD 700 cuft. 101″ Twin screw
Penta 7520 SD 840 cuft. 105″ Twin screw
Penta 1000-20 SD 1120 cuft. 116″ Twin screw
Penta 4120 HD 480 cuft. 102″ Single screw
Penta 5620 HD 630 cuft. 114″ Single screw
Penta 6720 HD 750 cuft. 103″ Twin screw
Penta 8020 HD 900 cuft. 101″ Twin screw
Penta 1120 HD 1300 cuft. 116″ Twin screw
Penta 1420 HD 1600 cuft. 145″ Twin screw
Penta 1720 HD 1850 cuft. 119″ Triple screw
Option: 16” rubber extension adds 70 cuft per screw.

Click here to see our Penta vertical TMR prices!

Call Post Equipment at (712)476-4500 or (712)470-1065 (cell).

Visit the Penta TMR website at www.pentatmr.com.

Read More

mixer-wagon-maintenance-quick guide

Quick Guide to Mixer Wagon Maintenance

Post Equipment has been buying, rebuilding, selling, and maintaining mixer wagons for a number of years. Here is a quick guide on how to maintain your farm equipment based on what we have seen in the field. The following notes are organized by vertical mixer wagons, reel feed wagons, and auger discharges. Call our knowledgable sales department for information you may need regarding your current or next feed mixer wagon.

Vertical Mixer Owner Notes

  • It takes at least a 450 cubic foot mixer to grind up a 5 x 6 bale of hay
  • It takes around 8 minutes to process a bale of alfalfa – longer for grass hay, cornstalks are similar to alfalfa
  • A single screw vertical mixer will unload faster than a twin screw because you have to wait for the feed to get from the back of the mixer to the front

VERTICAL MIXER MAINTENANCE:

Plow blade

  • The plow blade is the piece of metal on the back of the screw. On the new
    Pentas it is bolted on and it is welded on in most other wagons
  • Make sure the plow blade is not wore and is a ¼ “ from the side wall
  • Even though the plow blade looks like a small piece of metal (it is not along
    for the ride so to speak) it is a very important piece of the puzzle for fast
    and proper mixing action
  • If you need help with determining how worn your plow blade is or what
    action you should take, call Post Equipment and let us help you determine it

Mixer Knives

  • Check to make sure your knives are not dull if you are cutting a lot of hay or
    roughage (especially dairy)
  • If you are not worried about your knives and do not do a lot of cutting, check to
    make sure your bolt heads are not worn to the point where your knives
    will fall off. We’ve had this happen before and it can cause major damage.
  • If you are wondering how far to let you knives go before you replace them
    depending on your application give us a call.

Discharge

  • Make sure you have proper chain tension on the conveyor chain (3?of slack)
    and the hyd. motor drive chain (normal roller chain tight)

Planetaries

  • Make sure you have no leaks
  • Make sure the oil level is at the proper intervals
  • If you haven’t changed your oil in 2000 hours you should change it
  • 2 speed oil every 1000 hrs.

Reel Mixer Owner Notes

  • Red frame knights are older than yellow frame knights
  • A 2 spider reel is newer than a 3 spiral reel
  • A 2 spider reel takes a high roughage ration better than a 3 spider reel

REEL MIXER MAINTENANCE:

  • Take a look in your wagon and make sure your reel bars are not thin (especially where the bolt and the reel spring is). We have seen reel bars get so thin, break off, and then get stuck and cause auger damage.
  • Check your gear box for proper chain tension and their aren’t any tensioner springs broken. This is a common problem when we trade wagons in.
  • Make sure your bearings (set screws) are nice and tight on the augers and shafts.

Auger Discharge Owner Notes

  • Make sure your drive chains are tight
  • Make sure your augers are not worn
  • Make sure your auger bushings are not worn badly
  • Make sure your orbit motor is not leaking

You can read more about feed wagon maintenance in a recent post by Bud. Call Post Equipment if you need your mixer wagon repaired or replaced. 712-476-4500.

Read More

spread-all manure spreader

Manure Spreaders at Post Equipment

We recently discovered the heavy-duty Spread-All manure spreaders, made 100% in the USA in Cuming County, Nebraska. Customers came to us asking for the strongest, toughest manure spreader on the market. These spreaders are so reliable there is a waiting list for a used Spread-All; no one wants to sell it once they get one. West Point Design is the company that manufactures these industrial spreaders. The manufacturer has noted that the first Spread-All ever built has over 120,000 documentable loads and is still being run today. Watch the Spread-All video below and call Mike or Dan at Post Equipment for more information on Spread-All manure spreaders.  Office 712-476-4500 or Dan 712-470-2866. Here is a link to the manure spreaders on our lot today Manure Spreaders. More Spread-All’s coming to Post Equipment soon!

Read More

Bedding Cattle in the Snow

For quick, easy cattle feeding and bedding in the snow, now is the time to try a Roto-King Bale Processor.  Designed by an Iowa farmer, the Roto-King gets rid of ice on bales and there is no need to cut the strings off the bale before processing.  Call Post Equipment at 712-476-4500 for more information.

Read More