IH 5600 I Truck with Roda 2020 Manure Spreader

IH 5600 I Truck with Roda 2020 Manure Spreader (stock #2814) for sale at Post Equipment Corp. in Rock Valley, IA for $68,900

  • Nice unit!
  • Truck is a 2001 IH 5600
  • Cummins ISM 350V with 335 HP
  • 10 speed tranny
  • Tandem axle
  • Hendricks suspension
  • Roda 2020 vertical beater spreader
  • Poly floor
  • Good web chains
  • Truck has been service
  • New mud flaps!
  • Good beater teeth
  • Very nice spreader!
  • SN: 118

Call us at Post Equipment 712-476-4500 for more information on this unit!

Roda-2020-Vertical-Beater-Spreader-ID2814-2 Roda-2020-Vertical-Beater-Spreader-ID2814-3 Roda-2020-Vertical-Beater-Spreader-ID2814-4 Roda-2020-Vertical-Beater-Spreader-ID2814-5 Roda-2020-Vertical-Beater-Spreader-ID2814-6 Roda-2020-Vertical-Beater-Spreader-ID2814-7 Roda-2020-Vertical-Beater-Spreader-ID2814-8 Roda-2020-Vertical-Beater-Spreader-ID2814-9 Roda-2020-Vertical-Beater-Spreader-ID2814-10 Roda-2020-Vertical-Beater-Spreader-ID2814-11 Roda-2020-Vertical-Beater-Spreader-ID2814-12 Roda-2020-Vertical-Beater-Spreader-ID2814-13

Read More

Plastic Net Wrap

Plastic Net Wrap – Affecting my Cows & Mixer?

Does net wrap need to come off when processing bales in a vertical mixer?

Opinions vary, but most farmers do not take net wrap plastic off of their bales. If you are mixing feed for feeder cattle or fat cattle, no problem, leave it on! If you’re feeding dairy or stock cows, occasionally people will cut it off just to be safe due to the expected life span of the cattle, but most do not.

 

Does it affect the mixer wagon?

No, it does not affect the mixer’s vertical auger bearings at all! However, twine/plastic will build up on the discharge bearings in time, so it’s good to cut it off the bearings occasionally to keep it from damaging the bearing seals.

 

Overall, our personal opinion is it doesn’t seem to be that big of a deal to keep the twine or net plastic on. It’s your personal preference!

Read More

Mixer Wagon Seasonal Checkup

Mixer Wagon Seasonal Checkup

With new calves coming in and feeding high hay rations, be sure to check for worn out knives and thin auger flighting on your feeder wagon.

Those with vertical mixers should be aware that the plow blade/kicker on the bottom outside auger should be 1/4″ from the wall and the correct height for optimum mixing. The correct factory heights differ from brand to brand. Don’t know your correct height for mixing? Call 712.476.4500 for specs of your mixer wagon! Text a picture of your plowblade/kicker with the mixer model number to 712.470.1065 *This is very important for mix quality and cattle health.

Call us for all of your feeder wagon needs!

worn vs. new
Extremely worn out plow blade and leading edge on a vertical feeder wagon (**DO NOT let yours get even close to this bad!!)

Read More

Spreader Checklist

Manure Spreader Checklist

Soon the combines will start rolling and we all know what comes after that… loads and loads of manure will need to be hauled from yards and stock piles. Is your manure spreader ready for fall?

Here’s a few things to check over before you begin using your spreader this fall.

  1. Are all the bearings still good?
  2. Do all the zerks take grease?
  3. If your spreader has grease lines going to any bearings be sure to double check them – make sure the lines aren’t leaking anywhere before the grease reaches the bearings.
  4. Are the beater teeth getting thin?
  5. Are there any bolts missing? If so replace them *ASAP!!
    *if one were to come off it could be very dangerous as fast as they spin.
  6. How is the web chain tension?

Each brand has their own specs on these so check your owners-manual or give us a call and we can help!

Don’t forget about our shop and on-site service truck available 24/7 if you need assistance prepping your spreader for the manure hauling season!

*Remember if you get behind or just want an extra spreader we do have three rentals available. Give us a call at 712.476.4500 for more info!

Read More

Mixer Wagon Knives Sale

***MIXER WAGON KNIVES SALE***

 

Mixer wagon knives sale going on now through September 30, 2017!

Replacement Knives to fit Penta

(also fits Jaylor, Art’s Way, Diamond, Haybuster, Kirby, Maximixer & Valmetal)

Triangle Knife – Regular Price: $75.00      Sale Price: $70.00

Curved Knife – Regular Price: $79.00      Sale Price: $70.00

 

Supreme OEM Triangle Knife 

Regular Price: $84.00      Sale Price: $72.00

 

Universal Mixer Knife  – “It’s like getting two knives for the price of one!”

Regular Price: $84.00      Sale Price: $68.00 (until supplies lasts)

 

FREE BOLTS on all vertical mixer knives!

FREE SHIPPING on all mixer knife orders over $750.00 (lower 48 states only)!

 

Read More